Learning how to fix a dripping faucet starts with a familiar sound: it is 2 a.m. and the kitchen faucet is going drip ... drip ... drip into a stainless sink, loud enough to hear from the hallway. You tighten the handle a little harder. It slows for a minute, then starts again. That drip is not just an annoyance β a faucet leaking one drip per second wastes more than 3,000 gallons of water in a year, enough to fill a small swimming pool, and it can add $30 to $60 a year to a typical water bill. Left alone, the constant moisture also stains porcelain, pits chrome finishes, and wears a groove into the faucet's valve seat that turns a $5 repair into a full faucet replacement.
The good news is that most dripping faucets are fixed with basic hand tools, one trip to the hardware store, and about 30 to 60 minutes of your time. The repair almost always comes down to replacing a worn washer, O-ring, or cartridge β parts that cost between $10 and $30 total. The trick is knowing which of the four common faucet types you have, because each one comes apart differently.
Why Faucets Drip: The Mechanics in Plain English
Every faucet is a controlled leak. Inside the body, a movable part presses a seal against a fixed opening (the valve seat) to stop water flow. A kitchen faucet gets cycled 20 to 40 times a day, which means the sealing parts flex and compress thousands of times a year. Eventually the rubber hardens, cracks, or flattens β and water squeezes past.
Three components cause roughly 90 percent of drips. Washers are small rubber discs that press against the valve seat in older compression faucets; they flatten and split over 2 to 5 years of hard use. O-rings are thin rubber rings that seal around moving stems; when they dry out or crack, water leaks around the handle base or spout. Cartridges are self-contained valve units in modern faucets; their internal seals and ports wear out or get scored by mineral grit after 5 to 15 years. Hard water accelerates all of this: calcium and magnesium deposits act like sandpaper on rubber and score the smooth metal surfaces the seals press against. Our guide to how hard water affects homes explains the warning signs.
That last point matters because it explains the most common DIY failure. Homeowners replace the washer, the drip stops for a week, then it returns. The culprit is usually a corroded or grooved valve seat β the metal ring the washer presses against. A damaged seat will chew through a brand-new washer in days. We will cover how to inspect and dress the seat later in this guide.
How to Fix a Dripping Faucet, Step 1: Identify Your Faucet Type
Before you buy a single part, figure out which of the four designs you have. The repair steps, the parts, and the tools differ for each one. Look at the handles and how they move.
Compression Faucets
The oldest design, common in homes built before the mid-1990s. Two separate handles, one for hot and one for cold, and each handle turns multiple full rotations to open and close. If you have to crank the handle tighter and tighter over the months to stop a drip, it is almost certainly compression. Inside, a threaded stem drives a rubber washer down onto a valve seat. These are the simplest to repair and the parts are the cheapest β a washer assortment pack costs $3 to $8.
Cartridge Faucets
The most common modern design. One or two handles, and the handle moves up and down to control flow and side to side for temperature (single-handle), or each handle lifts and turns through a short arc (two-handle). Brands like Moen, Price Pfister, and American Standard use cartridges heavily. The cartridge is a plastic or brass cylinder containing all the valving; when it wears, you pull the whole unit and drop in a replacement costing $15 to $45 depending on brand. Matching the exact cartridge matters β there are hundreds of variants.
Ball Faucets
A single handle mounted on a rounded cap, usually over the kitchen sink, that pivots in every direction β the classic Delta design from the 1970s through the 2000s. Inside, a slotted metal or plastic ball rotates against spring-loaded rubber seats. Ball faucets have the most individual small parts (springs, seats, cam, packing), which makes them slightly fiddly, but complete repair kits cost only $10 to $20 and cover everything at once.
Ceramic Disc Faucets
The premium modern design. A single lever over a wide, flat cylindrical body, and the handle turns only a quarter-turn (90 degrees) from off to full-on. Inside, two polished ceramic discs slide against each other to open and close ports. Ceramic is extremely hard and long-lived β these faucets routinely go 15 to 20 years before dripping β but mineral grit can scratch the discs or the rubber inlet seals beneath them. Replacement disc cartridges run $25 to $60.
Step 2: Gather Tools and Parts
You do not need a plumber's truck for this job. Lay out the following before you start:
- Adjustable wrench and a set of screwdrivers (flathead and Phillips)
- Allen wrenches (many single-handle faucets hide a 1/8-inch or 3/32-inch set screw under the handle)
- Replacement washers, O-rings, or cartridge matched to your faucet
- Plumber's grease (silicone-based, about $5 a tube β petroleum grease degrades rubber)
- White vinegar and an old toothbrush for mineral deposits
- A towel or rag to plug the drain, plus a small container for screws
- Optional: valve-seat wrench ($8) and seat-dressing tool ($10 to $15) for compression faucets
Total parts cost for a typical repair runs $10 to $30. Washers and O-ring assortments are $3 to $8, brand cartridges $15 to $45, ceramic disc cartridges $25 to $60, and a ball-faucet rebuild kit $10 to $20. Buy the parts after you have disassembled the faucet and can match them exactly β or bring the old parts to the store, which counter staff at any hardware store will help you match in about two minutes.
Step 3: Shut Off the Water
Find the two angle stops under the sink β small football-shaped or oval valves on the hot and cold supply lines. Turn both clockwise until they stop. Then open the faucet handles to release pressure and confirm the water is off; a brief sputter is normal. If the angle stops are frozen, corroded, or spin without stopping the flow, do not force them with a cheater bar β you can snap a 20-year-old valve body and turn a drip into a flood. Instead, shut off the main water valve where the line enters the house (often near the water heater, in a garage, or in a ground-level utility box) and plan to have those angle stops replaced.
Once the water is off and the drain is plugged, you are ready to open the faucet up.
Repairing a Compression Faucet
- Remove the handle. Pop off the decorative cap (hot/cold button) with a flathead screwdriver to expose the handle screw. Remove the screw and lift the handle straight off. If it is stuck, wiggle gently β never pry against the sink deck with force.
- Remove the packing nut. You will see a hex nut around the stem. Hold the faucet body steady with one hand and loosen the nut counterclockwise with your adjustable wrench.
- Unscrew the stem. Turn the stem counterclockwise as if opening the faucet; the whole stem assembly threads out of the body.
- Replace the washer. At the bottom of the stem, a small brass screw holds the rubber washer. Remove the screw, swap in an identical washer, and reinstall the screw snugly. Replace the O-ring around the stem at the same time β it is pennies and prevents handle-base leaks.
- Inspect the valve seat. Shine a flashlight into the faucet body. The seat should be a smooth, even ring. If it is rough, grooved, or green with corrosion, dress it with a seat-dressing tool (a few light clockwise turns β do not grind aggressively) or replace the seat with a seat wrench if it is the removable type.
- Reassemble. Apply a thin film of plumber's grease to the stem threads and O-ring, thread the stem back in, tighten the packing nut firmly but not gorilla-tight, and reinstall the handle.
Compression stems should turn smoothly with light resistance. If a handle needs to be cranked hard to stop the drip after repair, the seat still needs attention.
Repairing a Cartridge Faucet
- Remove the handle. Look for a set screw on the underside or back of the handle (often hidden under a small cap or logo button). Loosen it with an Allen wrench and lift the handle off.
- Remove the retaining hardware. You will see either a horseshoe-shaped retaining clip (pull it straight out with needle-nose pliers) or a threaded retaining nut (unscrew with an adjustable wrench). Note the clip's orientation before removal.
- Pull the cartridge. Grip the cartridge stem with pliers (wrap it in a cloth to protect the finish) and pull straight up with a gentle twist. Note which way the cartridge faces β hot/cold orientation matters.
- Install the new cartridge. Match it exactly to the old one, apply plumber's grease to its O-rings, and slide it in with the same orientation. Reinstall the clip or nut.
- Reinstall the handle and test. Before fully reassembling, you can briefly turn the water back on to check for leaks around the cartridge.
Cartridge faucets are the most forgiving DIY repair because there is essentially one part to replace. The main risk is buying the wrong cartridge, which is why bringing the old one to the store is the single best move. If the new cartridge still drips, scrub mineral grit from the faucet body ports with vinegar and a toothbrush.
Repairing a Ball Faucet
- Loosen the cap. Remove the handle (set screw underneath), then loosen the rounded adjusting cap with adjustable pliers, protecting the finish with a cloth.
- Remove the internals. Lift out the cam (the plastic piece with the tab), then the ball itself. Under the ball you will find two small rubber seats held against the body by tiny springs β fish these out with an Allen wrench or your fingertip.
- Replace everything in the kit. Ball-faucet kits include new springs, seats, cam, O-rings, and sometimes the ball. Install the new springs and seats (springs go in first, narrow end down into the body), set the ball in place aligning its tab with the body slot, then the cam.
- Reassemble and adjust. Tighten the cap back on, reinstall the handle, and turn the water on. If it drips, tighten the adjusting cap an eighth of a turn at a time until it stops β overtightening makes the handle stiff and wears the new parts prematurely.
Ball faucets reward patience over force. The parts are small and the alignment tab on the ball must seat correctly, or the handle will bind. If the chrome ball itself is pitted, replace it too β a rough ball will destroy new seats within weeks.
Repairing a Ceramic Disc Faucet
- Remove the handle and escutcheon. Loosen the set screw, lift off the handle, then unscrew the decorative dome cap to expose the disc cartridge cylinder.
- Remove the cartridge. Unscrew the two or three screws (or the large retaining nut) holding the cylinder, then lift it straight out.
- Clean and inspect. The bottom of the cylinder has rubber inlet seals. Soak the cylinder in white vinegar for 30 minutes to dissolve mineral scale, scrub gently with a toothbrush, and inspect the ceramic discs for visible scratches or chips.
- Replace seals or the cartridge. If the discs look smooth, replacing just the inlet seals (a few dollars) often cures the drip. Scratched or chipped discs mean a full replacement cartridge.
- Reinstall carefully. Ceramic discs crack under uneven force β set the cylinder in straight, tighten screws evenly in a crisscross pattern, and do not overtighten.
Because ceramic disc faucets are the most expensive to buy, they are almost always worth repairing rather than replacing. A $25 to $60 cartridge restores a faucet that cost $150 to $400 new.
Step 4: Reassemble, Turn the Water On, and Test
With the new parts in place and everything reassembled, turn the angle stops back on slowly β a quarter turn, pause, then full open. Opening valves gradually prevents water hammer from slamming your fresh seals. Open the faucet to flush debris for 10 to 15 seconds, then close it and watch.
Testing takes patience. Close the faucet firmly but normally (do not crank it), dry the spout with a towel, and place a dry paper towel or cup under the spout. Check back in 10 minutes. A single residual drip from water trapped in the spout is normal; a continuing steady drip means something still is not sealing β recheck the seat, the part match, or the installation orientation. Also run both hot and cold and feel around the handle base and under the sink for any new leaks at the supply connections.
When the Faucet Body Itself Is Shot
Sometimes the faucet is the problem, not the parts. Replace the whole faucet instead of repairing when you see any of the following: the chrome or nickel finish is pitted and flaking (corrosion has reached the brass underneath); the valve seat is cracked, deeply grooved beyond dressing, or a non-removable type that is damaged; stem threads are stripped so the handle wobbles or will not stay tight; or the body itself has a hairline crack or mineral-eaten pinhole. A good rule of thumb: if the parts and specialty tools for a repair would cost more than half the price of a comparable new faucet, replacement is the smarter money.
A new mid-range kitchen or bathroom faucet costs $75 to $250, and professional installation typically adds $100 to $200, putting a full replacement at roughly $175 to $450 installed. Our bathroom and kitchen plumbing services cover full faucet replacement. If your faucet is over 20 years old, parts are discontinued, or you have already repaired the same faucet twice in a year, stop feeding it parts. If the drip persists after a careful repair, or you find corrosion damage during disassembly, a licensed plumber can confirm whether the body is salvageable β see our leak repair services or contact us for help.
Frequently Asked Questions
How much water does a dripping faucet waste?
A faucet dripping once per second wastes over 3,000 gallons per year β about 180 showers' worth of water. A faster drip can waste 5 to 10 gallons a day. At average U.S. water rates, a single slow drip typically adds $30 to $60 a year to the water bill, and hot-water drips cost more because you are also paying to heat the wasted water.
What is the most common cause of a dripping faucet?
Worn sealing parts cause about 90 percent of drips: flattened washers in compression faucets, cracked O-rings around stems, or worn cartridges in modern faucets. Hard water mineral deposits accelerate the wear by scoring rubber and metal sealing surfaces. If a new washer fails within weeks, the valve seat underneath is usually corroded or grooved and needs dressing or replacement.
How much does it cost to fix a dripping faucet yourself?
Most DIY faucet repairs cost $10 to $30 in parts: washer and O-ring assortments run $3 to $8, brand-name cartridges $15 to $45, ceramic disc cartridges $25 to $60, and ball-faucet rebuild kits $10 to $20. A basic adjustable wrench, screwdrivers, and plumber's grease are the only tools most jobs need. Professional faucet repair typically costs $100 to $250 including parts and labor.
How do I know what type of faucet I have?
Two handles that turn multiple full rotations indicate a compression faucet. A handle that lifts up and down (single-handle) or moves through a short arc (two-handle) indicates a cartridge faucet. A single handle on a rounded cap that pivots in all directions is a ball faucet. A single lever over a wide cylindrical body that turns only a quarter-turn is a ceramic disc faucet.
Can I still use the faucet while waiting for parts?
Yes, in most cases. You can shut off just that fixture using the angle stops under the sink and leave the rest of the house's water on. If the angle stops are frozen or missing, you can cap the supply or leave the main water on and simply avoid using that faucet until parts arrive. Never leave a disassembled faucet with the water supply open.
When should I replace the whole faucet instead of repairing it?
Replace the faucet when the finish is pitted or flaking, the valve seat is cracked or a damaged non-removable type, stem threads are stripped, or the body has a crack or pinhole leak. Also consider replacement if the faucet is over 20 years old with discontinued parts, or if the same faucet has needed repair twice within a year. A new mid-range faucet plus professional installation typically runs $175 to $450.
Drip Still Winning? We Will Fix It Fast
If the drip came back after your repair or the faucet body is corroded beyond saving, our licensed plumbers can diagnose it and fix or replace the faucet in a single visit. Reach out today and stop paying for water you never use.
π Call +1 (850) 904-1147