Outdoor spigot repair: plumber tightening the packing nut on an outdoor spigot with a wrench

That slow drip coming from the faucet on the side of your house is more than an annoyance — and outdoor spigot repair usually starts here. An outdoor spigot leaking at one drip per second wastes roughly 3,000 gallons a year, and if the drip is happening inside your wall, it can rot framing, grow mold, and undermine a foundation. The good news: most outdoor spigot problems are caused by two or three small parts that cost under ten dollars and take less than an hour to fix.

This guide walks through the full diagnostic process: how to tell whether the leak is a loose packing nut, a worn washer, or a freeze-split pipe, with step-by-step instructions for each repair — plus when to upgrade to a frost-free sillcock and when a leak inside the wall means calling a professional.

Outdoor Spigot Repair

Before you buy a single part, figure out exactly where the water escapes. Grab a flashlight and a dry rag, wipe down the spigot, then watch. There are four common leak points, and each one points to a different repair.

1. Water seeps around the handle or stem while the faucet is on or off. This is the packing nut, and it is the single most common cause of spigot leaks. The packing nut compresses a small ring of graphite or rubber packing against the stem to keep water from traveling up the shaft. Over years of use and seasonal temperature swings, the packing compresses and shrinks, and water finds its way through. This is a five-minute fix.

2. Water drips from the spout even when the handle is fully closed. This points to a worn washer or a damaged seat. Inside the valve, a rubber washer presses against a brass seat to stop the flow. Hard water grit, age, and simply being slammed shut for years wear the washer thin or carve a groove in the seat. This takes about 30 to 45 minutes to fix.

3. Water comes out of the threaded spout connection or a cracked spout body. A hose left attached through winter is the usual culprit. Water trapped in the hose and faucet freezes, expands with about 40,000 pounds of force per square inch, and splits the brass body or bursts the soldered joint behind it. You may only notice this in spring when you reconnect the hose and turn the water on.

4. Water stains the wall inside the house, or you hear water running in the wall when the spigot is on. This means the pipe behind the spigot has split from freezing. Stop here. The pipe runs through your wall cavity, and every minute of pressure pushes water into insulation, framing, and drywall. This is a job for a plumber with the right fittings and a way to open the wall cleanly. See the section on when to call a pro below.

⚠️
Watch for: If a hose or hose bib was left attached during the first hard freeze and now water pours out of the wall or the faucet body is visibly cracked, shut off the indoor supply valve to that spigot (or the main water shutoff) immediately and do not use the spigot until it is repaired.

Tools and Parts: What You Will Need

Almost everything here is standard garage inventory. For all four repairs, gather: an adjustable wrench (two are better — one to hold the valve body so you do not twist the pipe in the wall), a Phillips and flathead screwdriver, plumber's grease, Teflon tape, a bucket and old towels, and a utility knife. A basin wrench helps in tight spots but is rarely required.

For the packing nut fix, you need replacement packing — a coil of graphite packing string runs about $4 to $6 at any hardware store, or a pre-cut packing washer set runs $3 to $8. For the washer repair, buy an assorted washer kit ($5 to $9) or a stem repair kit made for your faucet brand ($6 to $14). A full replacement sillcock costs $15 to $35 for a standard brass model, or $25 to $60 for a frost-free version in 8, 10, or 12-inch lengths. In total, the DIY range for these repairs runs from about $5 for a washer to about $40 for a new frost-free sillcock plus tape and solder. If you call a plumber, expect $150 to $300 for a standard spigot replacement and $250 to $450 for a frost-free sillcock install that requires opening an interior wall.

Step 1: Tighten the Packing Nut (Try This First)

The packing nut is the hexagonal nut directly under the handle, around the stem. In roughly half of all service calls for leaking spigots, this is the only fix needed.

  1. Turn the spigot off fully. You do not need to shut off the house water for this repair.
  2. Place one wrench on the valve body to hold it steady — this is critical. Twisting the body can loosen the pipe connection inside the wall and turn a drip into a real leak.
  3. Place the second wrench on the packing nut and tighten it clockwise by one-eighth to one-quarter turn. Firm is fine; do not muscle it. Over-tightening makes the handle hard to turn and can crack the nut.
  4. Turn the water on and watch. If the seepage around the stem stops, you are done. Wipe it dry and check again after an hour.

If the nut is already as tight as it reasonably goes, or if tightening stops the leak but the handle barely turns, the packing material itself is worn out and needs replacing. Shut off the spigot, unscrew the packing nut fully, pull out the old packing with a pick or small screwdriver, wrap the new graphite packing string around the stem two to three times (or drop in the replacement packing washer), coat it lightly with plumber's grease, and reassemble. Snug the nut, test, and give it a final quarter turn.

ℹ️
Pro tip: Add a dab of plumber's grease to the stem threads every fall when you remove hoses for winter. A stem that turns smoothly puts far less wear on the packing and washers than one you have to force.

Step 2: Replace the Washer and Inspect the Seat

When water drips from the spout with the handle fully closed, the sealing washer at the end of the stem is no longer sealing against the valve seat. Here is the repair:

  1. Shut off water to the spigot. Most outdoor faucets have an indoor shutoff valve nearby, often in the basement, crawlspace, or utility room. If you cannot find one, shut off the main house water.
  2. Open the spigot fully to drain the line, then place a bucket under the faucet.
  3. Loosen and remove the packing nut, then unscrew the entire stem assembly counterclockwise out of the valve body. Hold the body with your second wrench the whole time.
  4. At the bottom of the stem you will find the washer, held by a small brass screw. Remove the screw, note the washer's size and shape (flat or beveled), and match it from your assortment kit. While you have it apart, look at the brass seat inside the valve body — it should be a smooth ring. If it is pitted, cracked, or deeply grooved, the washer will never seal properly.
  5. If the seat is just slightly rough, you can resurface it with a valve seat dresser (about $12), turning it gently until the surface looks even. If the seat is badly damaged or the valve body is cracked, replacing the whole sillcock is the better move.
  6. Install the new washer with the brass screw, coat the stem threads with plumber's grease, thread the stem back in, reinstall the packing nut, and snug it. Turn the water back on slowly and check for leaks at the stem and spout.

Budget about 30 to 45 minutes if the stem comes out easily. On older faucets, the stem may be corroded in place. Spray penetrating oil on the threads, wait 15 minutes, and try again. If the bonnet nut rounds off or the stem shears, that is your sign to replace the entire faucet rather than fight it.

Step 3: Replace the Whole Sillcock

Replace the full faucet when the body is cracked from freezing, the seat is too damaged to dress, the stem is seized, or the faucet is an older model with no vacuum breaker (an anti-siphon device that prevents hose water from being siphoned back into your drinking water — modern plumbing code requires one). Replacement also makes sense if you are already doing the work and want the freeze protection of a frost-free model.

First, determine how your spigot connects to the indoor pipe: threaded or soldered. A threaded connection unscrews from the pipe with two wrenches. A soldered connection requires cutting the pipe with a tubing cutter, cleaning the copper, and soldering the new sillcock with a propane torch, flux, and lead-free solder. If you have never soldered, a push-fit (SharkBite-style) sillcock costs about $10 more but needs no torch — cut the pipe square, deburr it, mark the insertion depth, and push the fitting on. Push-fit fittings are code-approved for behind-wall use and hold up to 200 PSI.

  1. Shut off the indoor supply to the spigot and drain the line.
  2. Working from inside (basement or crawlspace), disconnect the old sillcock. For threaded: hold the pipe with one wrench, turn the fitting counterclockwise with the other. For soldered: cut the pipe just behind the old fitting with a tubing cutter.
  3. Slide the new sillcock through the hole in the exterior wall from outside, caulk around the flange with silicone, and secure it with screws.
  4. Connect the indoor side — thread with Teflon tape and pipe dope, or solder, or push-fit.
  5. Turn the water on slowly, check both ends for leaks, then operate the spigot through several open-close cycles.

Measure the wall thickness before you buy. Sillcocks come in 4, 6, 8, 10, and 12-inch lengths measured from the flange to the pipe connection. Too short and the connection sits inside the wall where a leak hides; too long and it sticks out past the wall with unsupported pipe. Match the old length or measure the wall depth and pick the next size up.

Upgrade to a Frost-Free Sillcock

A standard spigot places the shutoff valve right at the exterior wall — the most freeze-exposed spot in your plumbing. A frost-free sillcock (also called a freeze-proof faucet) puts the actual valve seat 8 to 12 inches inside the house, where the wall cavity stays warm. When you turn the handle off, water drains out of the exposed portion automatically.

Frost-free models are the standard recommendation for any climate with freezing winters, including East Tennessee where overnight lows routinely drop into the teens and single digits. They are not magic, though: they only work if you remove the hose in fall. A hose left connected traps water in the stem, defeats the drainage design, and will split a frost-free faucet just as fast as a standard one. Also, the valve must be installed with a slight downward pitch toward the outside (about 1/4 inch of drop over its length) so water actually drains out instead of pooling in the barrel.

Cost comparison

A standard sillcock runs $15 to $35; a frost-free version runs $25 to $60. The extra $20 or so buys real protection against the most common cause of spigot failure. If you are replacing a freeze-damaged faucet, the incremental cost of upgrading is almost always worth it. Professional installation of a frost-free sillcock typically runs $250 to $450, mainly because the plumber often needs to open a small section of interior wall to reach the pipe connection.

When the Pipe Inside the Wall Is Split: Call a Professional

A split supply pipe behind the wall is the one spigot problem you should not DIY your way through. Signs include water staining on interior drywall near the spigot, the sound of water running inside the wall when the spigot is on, a musty smell developing near an exterior wall, or a water bill that jumps without explanation. Shut off the indoor supply valve to that line immediately, or the main water shutoff if you cannot find it.

The risk is not just the pipe repair itself — it is the water damage that accumulates while the leak runs. A supply pipe under 60 PSI can push several gallons per minute into a wall cavity. In 24 hours, that is enough to saturate framing, ruin drywall, and start mold growth, and insurance adjusters routinely deny or reduce claims when a known leak was left running. A plumber can open the wall surgically, replace the damaged section (often upgrading it to a freeze-resistant material), check the surrounding structure for damage, and repair the wall. If you are dealing with water damage in the wall, our leak repair and pipe repair services cover exactly this scenario, and if you notice the damage after hours, emergency plumbing is available around the clock.

Winterizing Outdoor Spigots: A 15-Minute Fall Routine

The cheapest repair is the one you never need. Every October, before the first hard freeze:

  • Disconnect every hose, drain it, coil it, and store it indoors. This single step prevents the majority of freeze-split spigots.
  • If your spigot has an indoor shutoff valve, close it, then open the outdoor spigot and leave it open. If the indoor valve has a bleeder cap, open it to drain the trapped section of pipe into a bucket.
  • Install an insulated faucet cover (about $5 to $10) over each outdoor spigot for extra protection, especially on north-facing walls and in windy locations.
  • Walk the house in spring before reconnecting hoses: turn each spigot on with a bucket underneath and watch for water coming from the handle, the body, or the wall penetration. Catching a freeze split in April is a $30 repair; discovering it in July when you finally water the garden is a $300 water bill and possibly a ruined wall.

If you notice low water pressure anywhere in the house while you are at it, the culprit is often elsewhere — low water pressure causes and fixes covers the full diagnostic. And if your annual checkup habit is still forming, our annual plumbing inspection checklist walks through the whole house in about an hour.

Mistakes That Turn Small Jobs Into Big Ones

Do not put thread-seal tape on hose-bib threads — the rubber washer in the hose coupling does the sealing, and tape makes it worse. Never force a corroded stem: if it will not turn after penetrating oil, replace the faucet, because a sheared stem turns a $10 repair into an emergency call. Install frost-free models with a slight downward pitch toward the outside so they drain, and make sure the replacement has a built-in vacuum breaker to protect your drinking water.

Frequently Asked Questions

How much does it cost to fix a leaky outdoor spigot myself?

Most DIY spigot repairs cost between $5 and $40 in parts. Tightening or repacking the packing nut runs $3 to $8, a washer replacement runs $5 to $14, and a full new sillcock runs $15 to $35 (standard) or $25 to $60 (frost-free). If you hire a plumber, expect $150 to $300 for a standard replacement and $250 to $450 for a frost-free install requiring interior wall access.

Can I just tighten the packing nut to stop a spigot leak?

Yes, and you should try that first — it fixes about half of all spigot leaks. Tighten the nut under the handle one-eighth to one-quarter turn while holding the valve body steady with a second wrench. If the seepage stops, you are done. If the leak persists or the handle becomes hard to turn, the packing material is worn and needs to be replaced, which takes about 15 minutes.

Why does my outdoor faucet still drip when it is turned off?

A drip from the spout with the handle fully closed means the rubber washer at the end of the stem is worn, or the brass valve seat it presses against is pitted. Shut off the indoor supply, remove the stem, replace the washer (matching the size and shape), and inspect the seat — a slightly rough seat can be resurfaced with a valve seat dresser, but a deeply grooved seat means the faucet should be replaced.

Should I replace my spigot with a frost-free sillcock?

If you live anywhere with freezing winters, yes. A frost-free sillcock moves the shutoff valve 8 to 12 inches inside the warm wall cavity so the exposed portion drains dry when closed. The upgrade costs about $20 more than a standard sillcock. Remember that it only works if you remove the hose every fall and install the faucet with a slight downward pitch toward the outside.

How do I know if the pipe inside the wall is split from freezing?

Watch for water stains on interior drywall near the spigot, the sound of water running inside the wall when the faucet is on, a musty smell near an exterior wall, or an unexplained jump in your water bill. If you see any of these, shut off the indoor supply valve to that spigot (or the main water shutoff) immediately and call a plumber — water under house pressure can flood a wall cavity fast.

Do I need to shut off the main water to replace a spigot washer?

Not necessarily. Most outdoor spigots have a dedicated indoor shutoff valve nearby, often in the basement, crawlspace, or utility room. Close that valve and open the spigot to drain the line before disassembling. If you cannot find a dedicated valve, shut off the main house water to be safe.

Spigot Leaking Inside the Wall?

If your leak goes deeper than a washer — a cracked faucet body, a split pipe in the wall, or water staining on interior drywall — our licensed plumbers can fix it fast before the damage spreads. Same-day service available.

📞 Call +1 (850) 904-1147
This guide is general information for homeowners, not a substitute for a licensed plumber’s assessment of your home. Gas lines, main sewer lines, and work behind walls or under slabs should be handled by a licensed professional. Sources: U.S. EPA WaterSense (epa.gov/watersense) · U.S. Department of Energy — Water Heating (energy.gov/energysaver/water-heating).